Recent content by cardiff

  1. C

    Arabsat BADR-8

    North-West of France with rain 11727 H 9.8 db 11766 H 9.8 db 11.996 H 14.2 db 12.563 V 14.2 db with Octagon SF8008 + Laminas 180
  2. C

    Jaeger 1224 East West limits

    here is the axis and the gear on which it must be fixed
  3. C

    Jaeger 1224 East West limits

    The metal axis is fixed on the gear (red arrow) it cannot come out upwards, the 3 other parties simply slide over it.
  4. C

    openatv 7.3

    With another image like openeight, it also does it or not ? and after a clean install of Open ATV 7.2 or 7.3 on the same slot? I have on my Combo OpenATV 7.2 slot1 Define os slot2 OpenATV 7.3 slot 3 OpenATV 6.4 slot4 and everything works fine
  5. C

    31.5W (Intelsat 25)

    Cherifla tv is also now on 34.5 W with Ortm and ECF TV (19 channels) on the frequency DVB-S2 8PSK 11527 V 12533 3/4 I seem to have not seen a thread on Intelsat 35e 34.5West
  6. C

    Server problem ?!

    Also problems posting PM. I have sending errors and it tells me to start over but it does not work correctly at all. Cardiff
  7. C

    New Lnb changer

    the divider mounted on a technirotor modified by Trust, everything is OK, thank's to JPC.
  8. C

    Top Tip T2-MI reception on E2 STB with SDG image - A complete step by step guide

    On satellites.xml 4.8E Ku-band Astra 4A <transponder frequency="12073000" symbol_rate="27500000" polarization="0" fec_inner="3" system="1" modulation="2" is_id="15" pls_mode="1" pls_code="0" t2mi_plp_id="0" t2mi_pid="4096" />
  9. C

    C-band LNB for Laminas 120

    This exists for the C band for the 180 laminas but not for the 120. "Laminas AS 1800 arm for C band LNB diameter 60mm"
  10. C

    Just Sharing This Modified my CM LNB holder for KU and CBAND

    I have the JPC positioner for 3 years,(first version built by myself) : a single box, a single remote control and more. If you have a problem, it will only come from your Polar mount installation or other H-H motors, and since the firmware has constantly evolved for the better. (as well as...
  11. C

    New Lnb changer

    Test done on the Technirotor Technisat only the measurements given are accurate Cardiff
  12. C

    New Lnb changer

    Hello zorrin, Sorry everything has been disassembled for more than 6 months and since then I have broken several fingers on my right hand and I can't do anything for the moment. Cardiff
  13. C

    New Lnb changer

    On my laminas 1800 with the Lnb Changer (which are completely dismantled) the original arms are used and the central arm was designed by Trust, he used at the time a laminas 1800 from another person for the adaptation for the Lnb Changer I do not have Channel Master 1.8m Cardiff
  14. C

    Jaeger smr 1224 adjustment-overhaul-maintenance

    Hello, The broken worm has been repaired by Trust (golden hands) I thank him very much. The 2 equally defective ball bearings have been replaced. The spigot has also been replaced since I had to drill it. Also made by Trust . Now everything is going well Cardiff
  15. C

    Jaeger smr 1224 adjustment-overhaul-maintenance

    Hello, I knew something was wrong with my Jaeger SMR 1224 After cleaning the worm I discovered that it was about to break. In addition this worm is very hard to disassemble and I did not succeed. I'm looking for someone who could find a solution to fix it or fix it for me. Thank you all for...
Top