Reply to thread

Message

<blockquote data-quote="jackpeas" data-source="post: 5299"><p>[updated:LAST EDITED ON 04-Jun-02 AT 08:17 AM (GMT)]HI, Iam going to remove the ADL non adjustable feed and installed ADL adjustable feed. Now where do I set the feed AT 35 5/8 manufacter say or 36''&nbsp; Otherwise if&nbsp; I try to set to the number othe side, I lose my 36''. .This is a International feed that what it say on the feed. Now where do the c-band LNB go? On the top 12'0clock or at the bottomat 6 oclock? My chaparral receiver book diagram say at the top. I have been going with servo motor(the writing go down so you can read it) I will try to get the feed thing out the way and move on. Thank you agian jackp n Chicago&nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp;&nbsp; Yes I remove the ADL non adjustable today. Now I have on the ADL adjustable scalar ring feed.I was check out the 4 leg (measure the lenght I think one is shorter) SO I tried to adjust it with washer.But it did not work(put washers under the leg to make it longer.When I did this the signal number got less and I took them out)Let me finish about the feedhorn. I installed it with the c-band at 12 oclock the signal reading went way over,100-99 but no picture. I got the ladder out and the tv so I can watch what was go on.I turn the feed and push it all the way in untill it hit the stop.Then I started to bring it out slowly very slowly. I pass the first line on the side and I started get a signal reading 30. I kept bring it out more the reading got better. When the reading got 100 signal quality 99 I stop.Now I had to get the feed in the center of the scalar ring(because you can cock feed the to one side .The number and line is only on one side) Now I think I am on the right track. Tonight my 36''venture&nbsp; arm starting to act up.The screen is saing phisical limit has been reach. It just move a little bit and stop again. I will check it in day light.I have other 24'' arm to change it out.(3 or 4)And I repair my other arms when they go bad.We will get there. jackp n Chicago</p></blockquote><p></p>

[QUOTE="jackpeas, post: 5299"] [updated:LAST EDITED ON 04-Jun-02 AT 08:17 AM (GMT)]HI, Iam going to remove the ADL non adjustable feed and installed ADL adjustable feed. Now where do I set the feed AT 35 5/8 manufacter say or 36'' Otherwise if I try to set to the number othe side, I lose my 36''. .This is a International feed that what it say on the feed. Now where do the c-band LNB go? On the top 12'0clock or at the bottomat 6 oclock? My chaparral receiver book diagram say at the top. I have been going with servo motor(the writing go down so you can read it) I will try to get the feed thing out the way and move on. Thank you agian jackp n Chicago Yes I remove the ADL non adjustable today. Now I have on the ADL adjustable scalar ring feed.I was check out the 4 leg (measure the lenght I think one is shorter) SO I tried to adjust it with washer.But it did not work(put washers under the leg to make it longer.When I did this the signal number got less and I took them out)Let me finish about the feedhorn. I installed it with the c-band at 12 oclock the signal reading went way over,100-99 but no picture. I got the ladder out and the tv so I can watch what was go on.I turn the feed and push it all the way in untill it hit the stop.Then I started to bring it out slowly very slowly. I pass the first line on the side and I started get a signal reading 30. I kept bring it out more the reading got better. When the reading got 100 signal quality 99 I stop.Now I had to get the feed in the center of the scalar ring(because you can cock feed the to one side .The number and line is only on one side) Now I think I am on the right track. Tonight my 36''venture arm starting to act up.The screen is saing phisical limit has been reach. It just move a little bit and stop again. I will check it in day light.I have other 24'' arm to change it out.(3 or 4)And I repair my other arms when they go bad.We will get there. jackp n Chicago [/QUOTE]

Verification