Fun Card problem

m_atef

Member
Joined
Jan 1, 2000
Messages
22
Reaction score
0
Points
0
My Location
Egypt
Dear All,

I have a problem concerning programming FUN cards, recently I had a fun card, when trying to program it I get the message " chip protected, erase chip and try again" and when trying to erase the card I get the same message. Please I need help to unlock the card.
I am using Elvis programmer and muliprogram 7 asoftware for programming.

Note: I found some cards like that and my old ones are working perfectly
 

Burnt Chips

Overclocker Supreme & General Mad B*st*rd
Joined
Jan 1, 2000
Messages
453
Reaction score
0
Points
0
Age
64
My Location
sunny manchester (i wish )
Had same problem a while back with 2 diff funcards. It seemed
that i had set wrong card type ie: c64 eeprom instead of c128
and my programmer had started to write to them, I only managed
to rescue 1 card the other died (rest its soul) Check card setting
check also com port setting, recheck elvis software, and if still no joy (a nice little service in the garden will do) and buy a replacement. DAVE.
 

rolfw

Believe it when I see it Admin.
Staff member
Joined
May 1, 1999
Messages
38,332
Reaction score
1,644
Points
113
My Satellite Setup
Technomate 5402 HD M2 Ci, DM7000s, Transparent 80cm Dish, Moteck SG2100 DiseqC motor, lots of legacy gear. Meters: Satlook Digital NIT, Promax HD Ranger+ spectrum analyser.
My Location
Berkshire
And of course if that lot doesn't work, you couldn't have picked a better time of year for the cards to die, they make really great windscreen scrapers. ;)

On a slightly more serious note though, I seem to remember a piece of software that would break down card protection, but haven't seen it of late.
 

Burnt Chips

Overclocker Supreme & General Mad B*st*rd
Joined
Jan 1, 2000
Messages
453
Reaction score
0
Points
0
Age
64
My Location
sunny manchester (i wish )
What ICE Big R (i was welding new panels on me van all weekend)
its been pissing down none stop here. So i think he`s best resting it underground.
 

Burnt Chips

Overclocker Supreme & General Mad B*st*rd
Joined
Jan 1, 2000
Messages
453
Reaction score
0
Points
0
Age
64
My Location
sunny manchester (i wish )
What ICE Big R (i was welding new panels on me van all weekend)
its been pissing down none stop here. So i think he`s best resting it underground.
A fool and his Funcards not easily parted (until he dies from a heartattack caused by stress when it dont program right)
 

rolfw

Believe it when I see it Admin.
Staff member
Joined
May 1, 1999
Messages
38,332
Reaction score
1,644
Points
113
My Satellite Setup
Technomate 5402 HD M2 Ci, DM7000s, Transparent 80cm Dish, Moteck SG2100 DiseqC motor, lots of legacy gear. Meters: Satlook Digital NIT, Promax HD Ranger+ spectrum analyser.
My Location
Berkshire
Sorry, I'd forgotten your location dave, it doesn't rain quite as much down here in the deep south.

PS. have you got hiccups?
 

Burnt Chips

Overclocker Supreme & General Mad B*st*rd
Joined
Jan 1, 2000
Messages
453
Reaction score
0
Points
0
Age
64
My Location
sunny manchester (i wish )
Yea i think we should sell you lot our water (we got plenty)
as for Ps (it went straight over me head) unless you meen have i been drinking, which would be NO,Still got a bit of an hangove from celebrating footy result yesterday.GOD I HATE THEM SCOUSERS LFC (well actually there mostly french and german)
 

rolfw

Believe it when I see it Admin.
Staff member
Joined
May 1, 1999
Messages
38,332
Reaction score
1,644
Points
113
My Satellite Setup
Technomate 5402 HD M2 Ci, DM7000s, Transparent 80cm Dish, Moteck SG2100 DiseqC motor, lots of legacy gear. Meters: Satlook Digital NIT, Promax HD Ranger+ spectrum analyser.
My Location
Berkshire
The PS. was referring to your duplicate post. ;)
 

Burnt Chips

Overclocker Supreme & General Mad B*st*rd
Joined
Jan 1, 2000
Messages
453
Reaction score
0
Points
0
Age
64
My Location
sunny manchester (i wish )
I see now (silly me) I was watchin XXp and must have had an hand tremble or simular (HONESTLY ).
 
Top