Help me about starsat SR-X1500D Super MK-II

[hamid200200]

i have starsat SR-X1500D Super MK-II satellate recivere and i want to upgrade it please instruct me how can i do it?

 

[acmorfe]

i also have the same receiver. when i try to upgrade my unit the display changes to A001 briefly then shows E011. what went wrong? please help. thanks.

steps i took:
1. connect pc and receiver via null modem cable
2. put receiver on standby (clock on display)
3. run STB5518.exe (latest from satsw.com)
4. browse/select *.bin, press Start
5. display changes to A001 (briefly) then changes to E011
left it like this for 30 minutes, nothing happens...

 

[DeepDiver]

i also have the same receiver. when i try to upgrade my unit the display changes to A001 briefly then shows E011. what went wrong? please help. thanks.

steps i took:
1. connect pc and receiver via null modem cable
2. put receiver on standby (clock on display)
3. run STB5518.exe (latest from satsw.com)
4. browse/select *.bin, press Start
5. display changes to A001 (briefly) then changes to E011
left it like this for 30 minutes, nothing happens...

I believe you should switch OFF and then ON again your receiver after you press START.

Hope it helps.

 

[acmorfe]

I believe you should switch OFF and then ON again your receiver after you press START.

Hope it helps.

Yes, i itried that too. When I turn the receiver ON (switch at the back) after pressing Start, the unit just goes ON (last channel viewed) -- no change or message on display.

Also, I tried to highlight "STB Setting" on the menu and press 1234 on the remote and nothing happens.

If it would help, here is the info shown on "About STB":
Date: 2004-07-08
S/W ver: 6.4.1
Loader: 1.1.2
Model: SR-X1500D Super MK II
Company: STARSAT
URL: www.star-sat.com

Also, when the E011 appears on the display, the STB5518 window (PC screen) shows "Send:5" (sent 5 bytes only?).

Thanks for the help.

 

[acmorfe]

just following up... thanks.

 

[acmorfe]

help me, please....
or maybe tell me to get a hammer to smash my MKII and just get a better one -- a 200CI, perhaps?
but please say something...
thanks.

 

[DeepDiver]

help me, please....
or maybe tell me to get a hammer to smash my MKII and just get a better one -- a 200CI, perhaps?
but please say something...
thanks.

I have no experience with the MKII....my knowledge is limited to the common features among Starsat receivers......but if you are going to buy a new one....200CI is ok, but make sure you get it with Model ID E224, and Hardware version 2.00

 

[acmorfe]

... make sure you get it with Model ID E224, and Hardware version 2.00

Is there a way to know the Model ID and Hardware version without turning on the receiver? Written on the box somewhere?

Thanks for the reply.

Cheers!

 

[DeepDiver]

Is there a way to know the Model ID and Hardware version without turning on the receiver? Written on the box somewhere?

Thanks for the reply.

Cheers!

I am afraid you'll have to access the MENU to find out......

 

[mdagohoy]

i also have the same receiver. when i try to upgrade my unit the display changes to A001 briefly then shows E011. what went wrong? please help. thanks.

steps i took:
1. connect pc and receiver via null modem cable
2. put receiver on standby (clock on display)
3. run STB5518.exe (latest from satsw.com)
4. browse/select *.bin, press Start
5. display changes to A001 (briefly) then changes to E011
left it like this for 30 minutes, nothing happens...

Hey ACmorfe, hows your starsat receiver now after i upgraded your software? Enjoy the show man.

 

[acmorfe]

DeepDiver, thanks for the assistance. I think it was the fact that I was using a USB-to-serial interface. About 200CI+, is there a problem with H/W ver7.00?

mdagohoy, thanks for the upgrade: mul**visio*, pl*yb*Y, CNN, E*roSpor*s, etc. No TFc yet -- maybe because of dish alignment and no AtlanticBird3 Info in new S/W.

THANKS FOR ALL THE HELP, GUYS!

 

[DeepDiver]

DeepDiver, thanks for the assistance. I think it was the fact that I was using a USB-to-serial interface. About 200CI+, is there a problem with H/W ver7.00?

No prob with h/w ver7.00, just when you go and download the update from satsw.com , make sure you get the 200CI_V7 file.

 

[acmorfe]

No prob with h/w ver7.00, just when you go and download the update from satsw.com , make sure you get the 200CI_V7 file.

thanks again, DD.

 

[acmorfe]

If I am in on open field (no buildings nor trees), in let's say Riyadh, what
satellites are in my "line of sight"? from what degrees to what degees in the azimuth? What if I am in Manila, Philippines?
was that clear?

thanks.

 

[Ylies]

hello deepdriver
i have a Starsat sr-x1200d
i have the same problem with my sat reciever
when i try to upgrade my unit the display changes to A001 briefly then shows E011. what went wrong? please help. thanks.
thanks to answer me because i know that your knowledge is limited to the common features among Starsat receivers......
thaks a lot ;-)
If it would help, here is the info shown on "About STB":
Date: 25-07-2007
Loader ver: 3.03
Model: CX


Hope I see you soon deep driver ;-)

 

[nadom]

i have the same reciver and i search for newer software for it but i don't find i'm sorry

 

[Topper]

i have the same reciver and i search for newer software for it but i don't find i'm sorry

You are obviously all completely useless at using a simple search engine it took me 2 minutes to find this