Reply to thread

Message

<blockquote data-quote="Rav" data-source="post: 201594" data-attributes="member: 199367">I've just flashed my first image (Gemini 2.8) on my 7020 and am about to install my first emu, Newcamd 6.10.&nbsp; I'm manually installing as I haven't set up my network yet as my new router will not arrive until tomorrow.I've done a lot of reading on installing emus in this forum, but am still a bit confused with this version of Newcamd in particular.When I open Dreambox Control Center and navigate to /var, there is no bin directory but bin -&gt; /usr/bin.&nbsp; I guess this is a pointer, so do I use this directory, or do I create a new /var/bin directory?Also, when navigating through the Newcamd distribution I'm not sure exactly which files go where, is there a definitive guide somewhere?&nbsp; I'm not using TuxBox Commander, is this what I'm supposed to do?Program files: /var/bin - newcamd, cardserver, cardspider, betad (were the old names cardserv and betadserv, or do I have to change them to this?)Config files: /var/tuxbox/config/newcamd - newcamd.conf, cardserv.cfg, betad.cfgKeys: /var/(tuxbox or no tuxbox?)/scce/constantcw - keylist, ppua, rsakeylist, tpscryptAU files: /var/scce - not sure which AU files go here, all of them?I also came across this thread <a href="http://www.satellites.co.uk/php-bin/forum/showthread.php?t=58818" target="_blank">http://www.satellites.co.uk/php-bin/forum/showthread.php?t=58818</a> where some of the filenames were changed, is this also something I must do?Can someone please tell me or point me to where I can find the definitive answer to which files go where and which filenames need changing as there seems to be some conflicting information.Finally, at the top of the Newcamd 6.10 readme it says something about &quot;please use drivers and libs from the last full release 6.08&quot;???</blockquote>

[QUOTE="Rav, post: 201594, member: 199367"] I've just flashed my first image (Gemini 2.8) on my 7020 and am about to install my first emu, Newcamd 6.10. I'm manually installing as I haven't set up my network yet as my new router will not arrive until tomorrow. I've done a lot of reading on installing emus in this forum, but am still a bit confused with this version of Newcamd in particular. When I open Dreambox Control Center and navigate to /var, there is no bin directory but bin -> /usr/bin. I guess this is a pointer, so do I use this directory, or do I create a new /var/bin directory? Also, when navigating through the Newcamd distribution I'm not sure exactly which files go where, is there a definitive guide somewhere? I'm not using TuxBox Commander, is this what I'm supposed to do? Program files: /var/bin - newcamd, cardserver, cardspider, betad (were the old names cardserv and betadserv, or do I have to change them to this?) Config files: /var/tuxbox/config/newcamd - newcamd.conf, cardserv.cfg, betad.cfg Keys: /var/(tuxbox or no tuxbox?)/scce/constantcw - keylist, ppua, rsakeylist, tpscrypt AU files: /var/scce - not sure which AU files go here, all of them? I also came across this thread [url]http://www.satellites.co.uk/php-bin/forum/showthread.php?t=58818[/url] where some of the filenames were changed, is this also something I must do? Can someone please tell me or point me to where I can find the definitive answer to which files go where and which filenames need changing as there seems to be some conflicting information. Finally, at the top of the Newcamd 6.10 readme it says something about "please use drivers and libs from the last full release 6.08"??? [/QUOTE]

Verification