Reply to thread

Message

<blockquote data-quote="nadal liu" data-source="post: 1036771" data-attributes="member: 401837">Hello, it is me again.As I said, I have a on line producing set of emp centauri 4x16 (mod), which is servicing my customers.I used the other output of a quad 11300 lnb on each of my 124e and 128e for this test during xmas break when I returned Taiwan.In the test, I used 2 zinwell mb68 6x8 ms and 4 splitters, and 4 online power inserters(12v, 18v).I didn't take photos, but the setup is like the below for each zinwell 6x8:zinwell mb68(either of the 4 ports of 22k on/off, 13v/18v)-&gt;4 way splitter-&gt;power inserter(which blocks dc from ms)-&gt;lnbthis way, I can combine as many as 4 zinwell mb68 and provide service to as many as 32 stbs.Note that you may need to have as many as 4 port transformers to provide 13v x 2 /18v x 2.In my case, I split the power transformer to provide dc to both of the 13v lnbs( 13v 22k off, 13v 22k on) and another split for 18v lnbs( 18v 22k off, 18v 22k on)The test was a success.&nbsp; The signal q value I get from 4 way split zinwell is 2 higher than its counterpart in emp centauri.I plan to try the same set up except this time I want to use a mod 11200 japanese lnbs, and the power transformer will be 12v and 15v for Japanese lnb standard.I However, I am worried about 22k sent by ms, will it reach power inserter or even lnb?If so, I need my 22k switch again.&nbsp; Also, the reason to the failure last time I use splitter and zinwell ms as well as mod 11200lnb.Thanks.</blockquote>

[QUOTE="nadal liu, post: 1036771, member: 401837"] Hello, it is me again. As I said, I have a on line producing set of emp centauri 4x16 (mod), which is servicing my customers. I used the other output of a quad 11300 lnb on each of my 124e and 128e for this test during xmas break when I returned Taiwan. In the test, I used 2 zinwell mb68 6x8 ms and 4 splitters, and 4 online power inserters(12v, 18v). I didn't take photos, but the setup is like the below for each zinwell 6x8: zinwell mb68(either of the 4 ports of 22k on/off, 13v/18v)->4 way splitter->power inserter(which blocks dc from ms)->lnb this way, I can combine as many as 4 zinwell mb68 and provide service to as many as 32 stbs. Note that you may need to have as many as 4 port transformers to provide 13v x 2 /18v x 2. In my case, I split the power transformer to provide dc to both of the 13v lnbs( 13v 22k off, 13v 22k on) and another split for 18v lnbs( 18v 22k off, 18v 22k on) The test was a success. The signal q value I get from 4 way split zinwell is 2 higher than its counterpart in emp centauri. I plan to try the same set up except this time I want to use a mod 11200 japanese lnbs, and the power transformer will be 12v and 15v for Japanese lnb standard.I However, I am worried about 22k sent by ms, will it reach power inserter or even lnb? If so, I need my 22k switch again. Also, the reason to the failure last time I use splitter and zinwell ms as well as mod 11200lnb. Thanks. [/QUOTE]

Verification