I want measurements channel master 2.4m dish offset

RimaNTSS

RimaNTSS

Super Moderator
Staff member
Joined
Jan 7, 2009
Messages
5,687
Reaction score
6,186
Points
113
Age
59
My Satellite Setup
Some SAT-related hardware.
My Location
N-E from Riga
Hi all! Questions: Does Channel Master 2.4m (RX version) has the same fitting for lower feedarm like one CM 1.8m antenna? And length of the original CM 2.4m antenna feedarms are ~ 1970mm and 1515mm?
 

Attachments

  • IMG_20240311_161408.jpg
    IMG_20240311_161408.jpg
    217.3 KB · Views: 32
  • IMG_20240311_161423.jpg
    IMG_20240311_161423.jpg
    416.9 KB · Views: 32
Manikm909

Manikm909

Small'ish Dish Man
Joined
Sep 10, 2020
Messages
2,484
Reaction score
1,171
Points
113
Age
48
My Satellite Setup
Channel Master 1.8M on Edision MIO 4K & GTMEDIA Combo, and CM1.2M on Octagon SF8008
My Location
Kent, UK
good question ! @nelson_b might be able to answer, as he has both...
 
nelson_b

nelson_b

Contributor
Joined
Jul 27, 2008
Messages
1,985
Reaction score
2,075
Points
113
Age
74
My Satellite Setup
Strong 4375 driving a 2.4 m Channel Master dual focus offset + Invcom Quad C120 K/U l.n.b. + BSC 421 and Zinwell C band l.n.b.,s - DR HD F15 - TM5302 - Octagon SX88+Optima - GT Media V7 - HD receivers. + other dishes currently in use - Antique 3.0 m Prodelin P.F. - Channel Master 1.8 m offset - Channel Master. 1.2 m.
My Location
North West Yorkshire - near Lancashire & Cumbria borders.
Manikm909 said:
good question ! @nelson_b might be able to answer, as he has both...
Click to expand...
Hi - RimanNTSS ---- and Manikm909
Im pretty certain the lower feed arm clamp is identical to the 1.8 one ... i will find time tomorrow to measure it.
Regards. .....
 
Channel Hopper

Channel Hopper

Suffering fools, so you don't have to.
Staff member
Joined
Jan 1, 2000
Messages
36,053
Reaction score
8,742
Points
113
Age
60
Website
www.sat-elite.uk
My Satellite Setup
A little less analogue, and a lot more crap.
My Location
UK
Yes, the Rx version I picked up a few years ago had a front end arrangement that was the same as the 1m and 1.2m dishes - ex VSAT -I have been installing.
 
nelson_b

nelson_b

Contributor
Joined
Jul 27, 2008
Messages
1,985
Reaction score
2,075
Points
113
Age
74
My Satellite Setup
Strong 4375 driving a 2.4 m Channel Master dual focus offset + Invcom Quad C120 K/U l.n.b. + BSC 421 and Zinwell C band l.n.b.,s - DR HD F15 - TM5302 - Octagon SX88+Optima - GT Media V7 - HD receivers. + other dishes currently in use - Antique 3.0 m Prodelin P.F. - Channel Master 1.8 m offset - Channel Master. 1.2 m.
My Location
North West Yorkshire - near Lancashire & Cumbria borders.
RimaNTSS said:
Hi all! Questions: Does Channel Master 2.4m (RX version) has the same fitting for lower feedarm like one CM 1.8m antenna? And length of the original CM 2.4m antenna feedarms are ~ 1970mm and 1515mm?
Click to expand...
I can confirm that the bottom feed arm clamp is identical for 1.8 and 2.4 dishes ...
its difficult to get a precise measure of the feedarms whilst they are on the dish .... see below my attempt to measure one of the side arms.

.DSC04885-Optimized.JPG DSC04886-Optimized.JPG
 
RimaNTSS

RimaNTSS

Super Moderator
Staff member
Joined
Jan 7, 2009
Messages
5,687
Reaction score
6,186
Points
113
Age
59
My Satellite Setup
Some SAT-related hardware.
My Location
N-E from Riga
Thanks, @nelson_b So, the long feedarm could be about 202cm (from the LNB-holder to the mounting hole). And the bottom feedarm is about 151cm?
 
nelson_b

nelson_b

Contributor
Joined
Jul 27, 2008
Messages
1,985
Reaction score
2,075
Points
113
Age
74
My Satellite Setup
Strong 4375 driving a 2.4 m Channel Master dual focus offset + Invcom Quad C120 K/U l.n.b. + BSC 421 and Zinwell C band l.n.b.,s - DR HD F15 - TM5302 - Octagon SX88+Optima - GT Media V7 - HD receivers. + other dishes currently in use - Antique 3.0 m Prodelin P.F. - Channel Master 1.8 m offset - Channel Master. 1.2 m.
My Location
North West Yorkshire - near Lancashire & Cumbria borders.
RimaNTSS said:
Thanks, @nelson_b So, the long feedarm could be about 202cm (from the LNB-holder to the mounting hole). And the bottom feedarm is about 151cm?
Click to expand...
Didn,t try measuring the bottom one (more difficult- and it started raining ) will try and look later when the weather clears somewhat ...
 
nelson_b

nelson_b

Contributor
Joined
Jul 27, 2008
Messages
1,985
Reaction score
2,075
Points
113
Age
74
My Satellite Setup
Strong 4375 driving a 2.4 m Channel Master dual focus offset + Invcom Quad C120 K/U l.n.b. + BSC 421 and Zinwell C band l.n.b.,s - DR HD F15 - TM5302 - Octagon SX88+Optima - GT Media V7 - HD receivers. + other dishes currently in use - Antique 3.0 m Prodelin P.F. - Channel Master 1.8 m offset - Channel Master. 1.2 m.
My Location
North West Yorkshire - near Lancashire & Cumbria borders.
RimaNTSS said:
I do not need precise, just rough size (+/- 5cm). Thanks
Click to expand...

Best i can do with the arm in position ..... i also have subreflector arms currently stored in my garage .

bottom arm 1.JPG bottom arm 2.JPG
 
Channel Hopper

Channel Hopper

Suffering fools, so you don't have to.
Staff member
Joined
Jan 1, 2000
Messages
36,053
Reaction score
8,742
Points
113
Age
60
Website
www.sat-elite.uk
My Satellite Setup
A little less analogue, and a lot more crap.
My Location
UK
Dimensions of the ones here on tape measure. The rx/tx support arms are a completely different length and have no end bolt
 

Attachments

  • 20240312_142616[1].jpg
    20240312_142616[1].jpg
    281.4 KB · Views: 22
  • 20240312_142654[1].jpg
    20240312_142654[1].jpg
    293.3 KB · Views: 20
  • 20240312_142700[2].jpg
    20240312_142700[2].jpg
    489.6 KB · Views: 20
Top