New Lnb changer

Channel Hopper said:
On a Fibo (or any other Gregorian dish), it would be more or less at the centre of the feed arm.

Most professional dishes have the feed attached directly to the backplate, not bolted to the reflector, and from memory the Fibo has a casting backplate which extrudes to the base of the reflector with the boom held by an allen bolt, unless my memory is failing.
Click to expand...
Thats right for the 90 cm Fibo , not for the 120 .
For the 120 I made the changer with the moto near to the dish
 
Trust1 said:
and I was afraid to ask 175 euro (ex postage)o_O
Click to expand...

Let us know if you are prepared to do this, and when you can do it. Definite order from me.......
 
scopus said:
Let us know if you are prepared to do this, and when you can do it. Definite order from me.......
Click to expand...
Yes I will , but maybe for those who want more then 3 lnb holders , I will have to charge a small amount extra .
So each of you tell me youre wishes , motor at top of feedarm , motor under dish , how many and what size of lnb holders enz.
 
Mine would be a motor under the dish for a Channel Master 1.8, a 3 way LNB holder one for C band and 2 x 40mm holders.
Is that OK ?
 
scopus said:
Mine would be a motor under the dish for a Channel Master 1.8, a 3 way LNB holder one for C band and 2 x 40mm holders.
Is that OK ?
Click to expand...
Ok ! C in the middle ?
 
@Trust1 : How many 40 mm LNB holder with 2 Cband LNB (including their conical feedhorn) it's possible to put on your lnb changer project for Channel Master 1.80m ?

My best configuration could be:

- 2 KU LNBf (one linear, one circular)
- 2 Cband: one Linear & one Circular,
- 1 SMW KA 'CD'and
- 1 KA "B"
- 1 KA "A"
- 1 : 40 mm holder for "test"

possible ? , if not what is the maximum ?

Thanks again for your proposal .
 
I would like 5 holders if possible.

2x C band side by side
3x Ku band side by side

Motor under dish. Will the motor be attached to the dish itself or to the main bracket?
 
Only the Scopus version can be made with a standard SG2100A by the 150º turn range ( only 180º gear inside )
For CJ and Feedsat there will be a rotor with a inside 360º gear neccesary , like the Dark motor (more expensive)
Turning by diseqc 1.2 without software and hardware limits , has still a restriction of 270º , but that will do (I think) I have to make a drawing and do some calculating .
The motor is attached together with the new feedarm with the 2 screws at the same place where the original lower tube was attached .
The side arms will be adjustable by M6 inox rod attached to inox brackets that also allows to attach strengthening rods at the backside of the dish .
Since everyone has its own kind of polarmount so you will have to attach those rods by yourselfs .
end of straiting rod.webp straiten back.webp straiting rod edge inside.webp
 
With the SG2100 under the dish , there might be a rain issue , maybe better to switch over to the Dark motor and make it the standard for the changers .
The F connectors are in a better position .

SG2100 rain problem.webp Dark motor.webp
 
extended support X.webp
Feedsat_DXer said:
@Trust1 : How many 40 mm LNB holder with 2 Cband LNB (including their conical feedhorn) it's possible to put on your lnb changer project for Channel Master 1.80m ?

My best configuration could be:

- 2 KU LNBf (one linear, one circular)
- 2 Cband: one Linear & one Circular,
- 1 SMW KA 'CD'and
- 1 KA "B"
- 1 KA "A"
- 1 : 40 mm holder for "test"

possible ? , if not what is the maximum ?extended support X.webp

Thanks again for your proposal .
Click to expand...
Lowering the feedarm and make the lnb support arm longer , gives a longer lnb radius , so more space .
I think all of them is possible
 
Chris1979 said:
How much for a gibertini 1.5 version please?
Click to expand...
Like John wrote , I have to know and see the dimentions , but maybe I can manage .
The price will be the same .
Can you show some pictures of the lower backside ?
 
Last edited:
Trust1 said:
Like John wrote , I have to know and see the dimentions , but maybe I can manage .
The price will be the same .
Click to expand...
I can get you photos ect, no problems. But no going to have the money for a a few months. So I will have to wait. But it sounds like you will have your hands full for a while :-)
 
@ Cris , Love to see some pics of your dish ,
@ John , did you open that Dark motor , what type nr ? is the main gear 360º ?
 
Trust1 said:
@ Cris , Love to see some pics of your dish ,
@ John , did you open that Dark motor , what type nr ? is the main gear 360º ?
Click to expand...



No, didn't open it up or drive it with any diseqc control from a receiver so it might have some E - W software limit set. It is exactly as it came in the box. All i did was connect 18 volts to it and did a manual E - W travel test with the motor buttons, which seems to give about 170 deg. I will try and do a video clip of it doing E / W travel if the site will allow a video file to load. I drilled my adapter plate , see rough preliminary drawing / pic , to take the 170 deg thing into consideration .... if it will go to 180 deg , i'll just pop another set of holes in it.
 

Attachments

  • ADAPTER PLATE..webp
    ADAPTER PLATE..webp
    243.8 KB · Views: 31
John said:
No, didn't open it up or drive it with any diseqc control from a receiver so it might have some E - W software limit set. It is exactly as it came in the box. All i did was connect 18 volts to it and did a manual E - W travel test with the motor buttons, which seems to give about 170 deg. I will try and do a video clip of it doing E / W travel if the site will allow a video file to load. I drilled my adapter plate , see rough preliminary drawing / pic , to take the 170 deg thing into consideration .... if it will go to 180 deg , i'll just pop another set of holes in it.
Click to expand...



... Couldn't do the video showing the travel speed etc due to file size. Picture shows maximum angles E-W for untouched Dark Motor so might be worth opening it up to see if there is any simple adjustment so as to achieve 180deg should anybody wish to put more than three units on the plate.
Travel speed is not too bad with 18.5 volts supply.
 

Attachments

  • IMG_2476 (3).webp
    IMG_2476 (3).webp
    283.3 KB · Views: 28
Back
Top