Going from 1m gibertini to 1.2 laminas - worth the cost \ hassle??

[jeallen01]

Just measured the diameter of the motor stub / pole on the DM on which the OP 125 L is mounted - it's 50mm.

PS: I suspect that both DM's here could well be clones of the original ALSAT (which disappeared some years ago) DM since they came from the same UK supplier - and, also, I have read that most, if not all, DM's currently on the market ARE clones. However, I somehow doubt that the diameter of the stub / pole would vary between those from "different sources".

 

[Lazarus]

50mm? That's 2" , I believe.

 

[jeallen01]

50mm? That's 2" , I believe.

"Approximately so" - in "old money"!

 

[Channel Hopper]

Just measured the diameter of the motor stub / pole on the DM on which the OP 125 L is mounted - it's 50mm.

PS: I suspect that both DM's here could well be clones of the original ALSAT (which disappeared some years ago) DM since they came from the same UK supplier - and, also, I have read that most, if not all, DM's currently on the market ARE clones. However, I somehow doubt that the diameter of the stub / pole would vary between those from "different sources".

Stab spacers

hi all i am looking for a set of stab ds-01 spacers so i can install my gibertini op125l dish onto a stab 120 hh motor. i have searched high and wide but no luck. can someone please point me in the correct direction please. many thanks

www.satellites.co.uk

 

[funtime261]

Here's what I'm going to use to make it fit on a TM-2600

 

[jeallen01]

Thanks - thus it would appear that I was "probably wrong" in saying that all "DM" motors seem to have the same diameter stubs / poles since the DM shown in you link appears to have a 55mm one!

Therefore anyone with a "DM" should measure the stub / pole diameter before buying a new dish.

 

[Manikm909]

Are there 2 types of gibertini 1.25 dish ? I've seen some which have a silver metal looking more rounded lnb holder and some have a more square lnb white painted lnb holder. I read there might be 2 versions a heavier and a lighter version .... thoughts..... thanks

 

[jeallen01]

Take a look at the Gibertini website pages for sat dishes

 

[Manikm909]

Take a look at the Gibertini website pages for sat dishes

I will be getting 2nd hand. Its more a question has there been differing versions over time...I'm sure I read there was an aluminium one and a steel one...maybe thats the difference signified by the differing lnb holders...?

 

[Chr0nik]

please delete

 

[Manikm909]

I will be getting 2nd hand. Its more a question has there been differing versions over time...I'm sure I read there was an aluminium one and a steel one...maybe thats the difference signified by the differing lnb holders...?

from the website:

• The dish is available in aluminium alloy or in steel powder painted with U.V. inhibited polyester-based finishes in RAL7035 (light grey) colour.

​

Antenna net weight with aluminum dish (kg)(³)	16.5
Antenna net weight with steel dish (kg)(³)	21.20

dilema is now which one are you getting second hand??? without being there to weigh it.

looks like the alu version, is just 3.5kg more than a Triax TD110

 

[jeallen01]

If in doubt, trying asking the seller.

 

[Manikm909]

yes, trouble is a lot of sellers, dont know what they're selling

 

[jeallen01]

If you do get a Gibby to mount on your DM, you might want to take a look here, from post #17 onwards, at the heath-robinson way I made up the additional "clamping plates" to beef up the existing DM->pole "U" bolt clamps - and, personally, I would advise doing something like that before any distortion of the latter happens (OTOH, I didn't realise that that might happen until it was nearly too late).

 

[Manikm909]

there are two models of the laminas ofc-1200.
not sure which to go for...the cheaper:

LAMINAS. OFC-1200 Offset Dish

or the slightly more pricey:
LAMINAS - OFC-1200G, OFC-1200P Offset Dish (the P one, dont need it heated, lol)
what dya reckon?

 

[RimaNTSS]

not sure which to go for...

Reflectors are exactly the same, so, I would go for cheapest one.

 

[sonnetpete]

Without referring to the Laminas site, the 1200 has the three thin tubular arms to support the LNB (like mine) and the 1200P has two tubular support arms and a square section arm for the LNB. It was possible to buy the square arm etc to replace the three tubular ones. I think the "P" arrangement would be slightly more rigid but as has been pointed out the reflectors are the same...

 

[Channel Hopper]

Looking to the two links, the dish faces are constructed differently ( they may be from a similar mould), the position of the feed arm supports and the back bracket holes are for another size of bolt.

 

[Manikm909]

Well guys - i finally did it....
My new Laminas OFC-1200 arrived on Friday and i managed to put it up yesterday (in between rain showers and crazy winds). It needs a minor alignment tweak, but all is well - getting 45w to 52e
I couldn't believe how light the dish was, I could lift it up one handed even with bracket / lnb poles and lnb - so was easy to get it up ladder onto motor.
Ive attached some pics for your enjoyment
Oh yes, i moved the bottom bracket as i DID need more clearance to accoomdate the larger size, and the fact the AZ bracket is in the centre of the Laminas.
I have a pic, of the Laminas, my Triax TD110 and Gibertini to show size differences....

 

[Captain Jack]

It's surprising how light Laminas dishes are. My 1.8m one is only 17kg or thereabouts, whereas the same sized Channel Master is double that. Was a good performer too... Pity it's sat in the garage doing nothing.