Top Tip T2-MI reception on E2 STB with SDG image - A complete step by step guide

[EnoSat]

and tsduck ?
PS: fix pid for 3977 (pid 64 not use)

 

[rom2005]

and tsduck ?
PS: fix pid for 3977 (pid 64 not use)

I don't have tsduck installed and I can't use it. I don't like it anyway, but maybe there will be someone who will continue the experiments. Yet.

 

[EnoSat]

maybe problem with PCR, not use standart pid 1FFF and not sychronize in FW

 

[mike1]

FlySat Eutelsat 9B @ 9° East

www.flysat.com

Zeonbud is back via 9 E

Anyone had any luck??

 

[CrazyCat]

Signal some better comparing with 4.8E and marked as CCM in MATYPE

 

[CrazyCat]

And 4.8E transponders
P.S. Motorized dish Strong 0.95m with ALPS BSTE8-751B Ku-Universal LNB

 

[rom2005]

FlySat Eutelsat 9B @ 9° East

www.flysat.com

Zeonbud is back via 9 E

Anyone had any luck??

But it is encrypted by an unbroken system, identical to 4.8 ° E!

 

[EnoSat]

It might be worthwhile to see if the flooded ZeonBud CAM modules can decode the DATA stream

 

[rom2005]

astra --analyze "t2mi://#t2mi_pid=4096&t2mi_input=http://127.0.0.1:8001/1:0:1:1:48:10:30B022:0:0:0"

I wanted to analyze one tp of Zeonbud, but even this no longer works!

 

[rom2005]

maybe problem with PCR, not use standart pid 1FFF and not sychronize in FW

I don't know what this is about. What, where, how?

 

[EnoSat]

I wanted to analyze one tp of Zeonbud, but even this no longer works!

first must decode 4096 pid

 

[Mihay82]

Здравствуйте, помогите, если сможете, настраиваю T2MI по инструкции и в конце при переключении каналов выдает ошибку "ssid not found in pat", если при создании сервиса в "Openboxebit" поставить галочку не на DVB / TS, но на не-TS, то каналы отображаются, но смешанные. На каком этапе могла быть сделана ошибка?
Обновился спутниковый файл .xml, не помогло.
Заранее спасибо.

Please post in English from now on.

Translated,

Hello, help, if you can, I set up T2MI according to the instructions and at the end, when switching channels, it gives the error "ssid not found in pat" channels are displayed but mixed. At what stage could the mistake have been made?
Updated satellite .xml file, did not help.
Thanks in advance.

 

[EnoSat]

first check stream

 

[CrazyCat]

What Openboxebit ?

 

[Mihay82]

What Openboxebit ?

I apologize, the original text was like this (double translation from russian-english-russian):
Hello, help if you can, I configure T2MI according to the instructions and at the end when switching channels I get the error "ssid not found in pat", if when creating a service in "Openboxebit" put a check mark not on DVB/TS, but on non-TS, then the channels show, but are mixed. At what stage could a mistake have been made?
The file satellite.xml updated, did not help.
Thank you in advance. I hope it's clearer this way.

And I created the services in the program-dreamboxEDITSorry dreamboxEDIT

 

[Mihay82]

first check stream

Sorry, did you mean to do the flow analysis using the PLP parameter, or show you the analysis I performed earlier?

 

[EnoSat]

if astra analyze show data , then wrong astra.conf or userbouquet.tv

 

[Mihay82]

if astra analyze show data , then wrong astra.conf or userbouquet.tv

Most likely, the error is in astra. conf (I have it called-config. lua), since the userbouquet.tv changed to dreamdoxedit,

 

[Mihay82]

Please see what I'm doing wrong? Maybe it's the image I have OPENPLI 7.0

 

[otokoc]

Сделал Stream relay T2-MI транспондеров со спутника 40.5°W - SES 6 в С band,всё что доступно на 1,8м антенну по приёму у меня на Западе Украины.

Это: 3887 L,3999 L,4012 L,4099 L,4183 L. Всё работает отлично!


I made Stream relay T2-MI transponders from the satellite 40.5 ° W - SES 6 in C band, everything that is available on a 1.8m antenna for receiving in my West Ukraine. These are: 3887 L, 3999 L, 4012 L, 4099 L, 4183 L. Everything works perfectly!

hi vitalik

have you ses6 40.5w for setting?